AWWA M PE Pipe – Design and Installation. Document Language: English; Published By: American Water Works Association (AWWA); Page Count: PE Pipe – Design and Installation MANUAL OF WATER SUPPLY PRACTICES M55, First Edition AWWA MANUAL M55 First Edition American Water Works. AWWA M55 is not a standard, but rather a design manual according to the recommendations of the American Water Works Association (AWWA) covering all .

Author: Faelar Nikozil
Country: Myanmar
Language: English (Spanish)
Genre: Software
Published (Last): 20 May 2008
Pages: 35
PDF File Size: 16.69 Mb
ePub File Size: 6.13 Mb
ISBN: 481-9-58620-133-4
Downloads: 60694
Price: Free* [*Free Regsitration Required]
Uploader: Tokinos

This process is similar to extrusion in that the major operational steps are the same: Proper engineering design of a system will consider the type and effectiveness of the techniques used to join the piping components and appurtenances as well as the dura- bility of the resulting joints. Paperbackpages.

Pe Pipe Design And Installation (M55) (Awwa Manual)

The code letters for color and W stabilizer are A-for natural B-for colored C-for black with minimum 2 percent carbon black D-for natural with UV stabilizers E-for colored with W stabilizers PE pipe compounds are typically black with a minimum of 2 percent carbon black, C, or colored with W stabilizers, E.

Off-highway vehicles may be considerably heavier than H20 trucks, and these vehicles frequently operate on unpaved roads, which may have uneven surfaces. Research in the area of slow crack growth combined with continual advancements in material science have awa in HDPE piping products that when manufactured and installed in accordance with these standards are designed to provide sustained resis- tance to slow crack growth phenomena such as environmental stress cracking.

M5 determine the surge pressure in a PE pipeline for a different sudden velocity change, multiply the Table surge pres- sure for 1. The electrical energy passing through the integral heating element creates heat, which melts and expands, and then heats and melts the mating pipe surface.

  BYBEL 1953 PDF

Skip to main content.

Corrosion PE used in water piping applications is an electrically nonconductive polymer and not adversely affected by naturally occurring soil conditions. Aligning the fitting to the pipe and if necessary securing the fitting with a holding clamp.

– ATV A Standard vs. AWWA M55 manual

Both test methods measure the ability of a PE specimen to absorb energy on failure. The die shapes the extrusion melt into a cylinder of slightly greater size than the final pipe product. Howardg for the Bureau of Reclamation. Lists with This Book. Removing the heater and applying force awa join and fuse the melted surfaces together. Properly made heat fusion joints are fully restrained and do not leak.

Joining methods that do not provide restraint against m555 are not acceptable for use in PE pressure piping systems. Although simple in concept, the extrusion process used in the manufacture of plas- tic pipe employs a series of fairly sophisticated equipment that reliably and continu- ously performs the functions of feeding, melting, and mixing the material, delivering zyxwvu it to the die at appropriate and consistent awa, accurately shaping and sizing the pipe, and cooling and cutting awww coiling the product to precise lengths.

The embedment materials are coarse-grained, stable, and have been compacted to at least 85 percent Standard Proctor Density. Because there is no surcharge directly above the pipe centerline, an imaginary surcharge load of the same pressure per unit area as the actual load is applied to the subareas c and d. Securely fastening the components to be joined.


The load- ing for a semitrailer and tractor is designated HS20 and is shown in Figure Parts processed from PE are essentially isotropic in their properties. Some of the values are as follows: The second mode of pipe failure is the result of slow crack growth.

Most mechanical fittings can be installed with basic hand tools. The designer should be aware, however, that all piping systems are susceptible to permeation of light hydrocarbon contaminants that may be present in the soil. The receiver should have a procedure for reconciling any such discrepancies. When swwa pipe is received, it should be visu- ally inspected to verify that the correct product was received. Therefore, the pipe producer gener- ally monitors those process control variables that are determined as quality critical.

See Working Pressure Rating section. Aawwa use, inspect slings and lifting equipment. With the addition of an zy zyxwvu impact factor, the method, which follows, may be used to find the load under a heavy wawa where the tire pattern, also called the tire imprint area, is known.

Pipes are subject to one of the following pressure tests: The concept is that soil settlement around the buried pipe occurs in dynamic, discrete events as soil grains shift or fracture. The addition of 2 to 2.

Most 10 Related

  • ISO 7886-3 PDF
  • ISO 12215-6 PDF
  • ATV DVWK A 127 PDF
  • ASTM D4218 PDF
  • ASTM F2129 PDF